PURE DATA, LTD. SATISFAXTION MODEM/200 Card Type Modem(asynchronous) Chip Set Intel Maximum Data Rate 2400bps Maximum Fax Rate 9600bps Data Bus 16 bit ISA Fax Class Class I & II Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis Fax Modulation Protocol Unidentified Error Correction/Compression MNP5, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Line in CN1 Unidentified CN3 Line out CN2 Proprietary AT Command Set ACCEPT RELIABLE CONNECTION Type: Configuration Format: AT [cmds] \U [cmds] Description: Accepts remote modem’s request for MNP reliable link. AUTO-RELIABLE FALLBACK CHARACTER Type: Configuration Format: AT [cmds] %An [cmds] Default: 19 Range: 0-127 Unit: ASCII Description: Sets the character used as the auto-reliable fallback character AUTO-RELIABLE TIME BUFFER CONFIGURATION Type: Configuration Format: AT [cmds] \Cn [cmds] Description: Controls the handling of incoming data during auto-reliable time period Command Function \CO Disabled \C1 Enable 200 character buffer. If 200 characters received without reliable character, establish normal connection \C2 Auto reliable buffer disabled. Establish normal connection on receipt of escape character BIT-MAPPED REGISTER S14 Format AT [cmds] S14=n [cmds] Default: 138 Range: 0-174 Unit: Bit-mapped Description: Controls echo, result codes, result code display, dial mode, and answer/originate mode Bit Value Function 0 0 Not used 1 0 Command echo disabled 1 Command echo enabled 2 0 Result codes enabled 1 Result codes disabled 3 0 Display result codes in numeric format 1 Display result codes in verbose format 4 0 Not used 5 0 Tone dial enabled 1 Pulse dial enabled 6 0 Not used 7 0 Answer mode enabled 1 Originate mode enabled BIT-MAPPED REGISTER S21 Format AT [cmds] S21=n [cmds] Default: 48 Range: 0 - 254 Unit: Bit-mapped Description: Controls S23, CTS action, DTR action, DCD action, DSR action and the Long Space Disconnect function. Bit Value Function 0 0 Not used 1 0 Option 1 for bits 1, 2 and 3 of S32 enabled 1 Option 2 for bits 1, 2 and 3 of S23 enabled 2 0 CTS signal normal 1 CTS signal forced high 4, 3 00 DTR signal ignored 01 Modem goes to command mode on low DTR 10 Modem disconnects on low DTR. Auto-Answer is disabled 11 Modem is initialized on low DTR 5 0 DCD signal forced high 1 DCD signal normal 6 0 DSR signal forced high 1 DSR signal normal 7 0 Long Space Disconnect function disabled 1 Long Space Disconnect function enabled BIT-MAPPED REGISTER S22 Format AT [cmds] S22=n [cmds] Default: 118 Range: 0-255 Unit: Bit-mapped Description: Controls speaker, result codes and make/break ratio Bit Value Function 1, 0 00 Off volume 01 On volume 10 Medium level volume 11 High level volume 3, 2 00 Speaker off 01 Speaker off on carrier 10 Speaker always on 11 Speaker on during handshake 6, 5, 4 000 Blind dial and basic result codes only enabled 100 Blind dial and basic and connection speed result codes enabled 101 Blind dial and basic and connection speed result 110 codes and dialtone detection enabled 111 Blind dial, basic and connection speed result codes and dialtone detection enabled Blind dial, basic and connection speed result codes, busy and dialtone detection enabled 7 0 Make/Break pulse ratio at 39/61 1 Make/Break pulse ration at 33/67 BIT-MAPPED REGISTER S23 Format AT [cmds] S23=n [cmds] Default: Unidentified Range: 0-191 Unit: Bit-mapped Description: Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone Note: See S21 bit one to set option 1 and 2 Bit Value Function 0 0 Remote digital loopback ignored 1 Remote digital loopback accepted Option 1 (bit 1 of S21 = 0) 3, 2, 1 000 Sets serial port speed to 0-300bps 001 Sets serial port speed to 1200bps 010 Sets serial port speed to 2400bps 011 Sets serial port speed to 4800bps 101 Sets serial port speed to 9600bps 110 Sets serial port speed to 19.2Kbps 111 Sets serial port speed to 38.4Kbps Option 2 (bit 1 of S21 = 1) 3, 2, 1 000 Sets serial port speed to 12.0Kbps 001 Sets serial port speed to 14.4Kbps 010 Sets serial port speed to 57.6Kbps 5,4 00 Parity even 01 Parity space/no parity 10 Parity odd 11 Parity mark 7, 6 00 Guard tone disabled 01 550Hz guard tone enabled 10 1800Hz guard tone enabled BIT-MAPPED REGISTER S27 Format AT [cmds] S27=n [cmds] Default: 73 Range: 0 - 255 Unit: Bit-mapped Description: Controls communications mode, line type, and protocol type Bit Value Function 0 0 Not used 1 0 Not used 7, 2 00 Switched line 01 Leased line 10 Not used 11 Leased line 3 0 Not used 4 0 Not used 5 0 Not used 6 0 Select CCITT protocols 1 Select Bell protocols BREAK SEND Type Configuration Format AT [cmds] \Bn [cmds] Default 3 Range 1 -9 Unit .1 second Description Sends break of n BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Break from DTE Break from DTE Break from remote while in command modem mode \K0 Enter command Buffers cleared Buffers cleared mode, do not and break sent to and break sent to send break to remote modem remote modem remote modem \K1 Buffers cleared Buffers cleared Buffers cleared and break sent and break sent to and break sent to to remote modem remote modem remote modem \K2 Enter command Send break to Send break to mode, do not remote modem remote modem send break to immediately immediately remote modem \K3 Send break to Send break to Send break to remote modem remote modem remote modem immediately immediately immediately \K4 Enter command Send break to Send break to mode, do not remote modem with remote modem with send break to transmitted data transmitted data remote modem \K5 Send break with Send break to Send break to transmitted remote modem with remote modem with data transmitted data transmitted data COMPRESSION Type: Configuration Format: AT %Cn Description: Selects MNP5 data compression Command Function %C0 Data compression disabled %C1 Data compression enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Sets connect mode Command Function \N0 Normal mode enabled \N2 MNP mode enabled \N3 LAPM mode enabled \N4 LAPM mode enabled FLOW CONTROL Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects modem port flow control Command Function \G0 Flow control disabled \G1 Flow control enabled FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bidirectional XON/XOFF flow control enabled \Q2 CTS flow control by DCE enabled \Q3 Bidirectional CTS/RTS flow control enabled \Q4 XON/XOFF flow control by DCE enabled \Q5 CTS flow control by DCE enabled. CTS low until connection established \Q6 Bidirectional CTS/RTS flow control enabled. CTS low until connection established INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Default: 0 Range: 0-90 Unit: 1 minute Description: Sets the length of time that the modem does not receive information before it disconnects LOCK SERIAL PORT Type: Configuration Format: AT [cmds] \Jn [cmds] Description: Sets operation of serial port speed Command Function \J0 Serial speed locked \J1 Serial speed follows connect speed LOOPBACK TESTS Format AT [cmds] S16=n [cmds] Default: 0 Range: 0 - 125 Unit: Bit-mapped Description: Enables loopback tests Bit Value Function 0 0 Local analog loopback test disabled 1 Local analog loopback test enabled 1 0 Not used 2 0 Local digital loopback test disabled 1 Local digital loopback test enabled 3 0 Modem is not performing remotely requested remote digital loopback test 1 Modem is performing remotely requested remote digital loopback test 4 0 Modem is not performing locally requested remote digital loopback test 1 Modem is performing locally requested remote digital loopback test 5 0 Remote digital loopback with local self-test disabled 1 Remote digital loopback with local self-test enabled 6 0 Local analog loopback with local self-test disabled 1 Local analog loopback with local self-test enabled MAXIMUM BLOCK SIZE FOR TRANSMISSION Type: Configuration Format: AT [cmds] \An [cmds] Description: Sets the maximum transmittable block size Command Function \A0 MNP block size is 64 characters \A1 MNP block size is 128 characters \A2 MNP block size is 192 characters \A3 MNP block size is 256 characters MNP STREAM/BLOCK MODE Type: Configuration Format: AT [cmds] \Ln [cmds] Description: Selects the transfer mode for MNP Command Function \L0 Stream mode for MNP enabled \L1 Block mode for MNP enabled RESULT CODE FORMAT Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects format for information-text and result codes Command Function V0 Numeric format enabled V1 Verbose (word) format enabled SWITCH TO NORMAL MODE Type: Configuration Format: AT [cmds] \Z [cmds] Description: Switches to normal mode from MNP mode TEST TIME LIMIT Type Configuration Format AT [cmds] S18=n [cmds] Default 0 Range 0 - 255 Unit 1 second Description Limits time allowed for diagnostic test V.42 DETECTION PHASE Type: Configuration Format: AT [cmds] -Jn [cmds] Description: Controls V.42 detection Command Function -J0 V.42 detection disabled -J1 V.42 detection enabled V.42bis COMPRESSION CONTROL Type: Configuration Format: AT [cmds] "Hn [cmds] Description: Controls V.42bis data compression Command Function "H0 V.42bis disabled "H1 V.42bis when transmitting enabled "H2 V.42bis when receiving enabled "H3 V.42bis when transmitting/receiving enabled V.42bis MAXIMUM STRING LENGTH Type: Configuration Format: AT [cmds] "O=n [cmds] Default: 250 Range: 6 -250 Unit: Unidentified Description: Selects string size for V.42bis compression XON/XOFF PASS-THROUGH Type: Configuration Format: AT [cmds] \Xn [cmds] Description: Selects whether XON/XOFF signals are sent to remote modem Command Function \X0 XON/XOFF signals trapped by local modem \X1 XON/XOFF passed through local modem